833-336-3270 Option 4
Signed in as:
filler@godaddy.com
Class Descriptions
Smart Equipment (SE) Controls -Commercial Class
Smart Equipment (SE) Controls -Commercial Class
Smart Equipment (SE) Controls -Commercial Class
The course will provide an overview of the Simplicity SE control
features that are included with the board, optional add on boards are covered as well. Basic equipment set up with the board will be discussed as well as the interaction with the SE Control, MAP Gateway and remote control.
Cost: FREE
Hx Thermostat and Zoning Installation & Troubleshooting
Smart Equipment (SE) Controls -Commercial Class
Smart Equipment (SE) Controls -Commercial Class
This course will cover Hx Thermostat and Hx Zoning installation and troubleshooting. Proper set up, wiring, configuration and navigation will be discussed. This course is intended for installer and service technician who install the Hx Thermostats and HX Zoning systems. This class is divided into 2 sessions. Session 1 will cover Hx Thermostat Operation, session 2 will cover Hx Zoning.
Cost: FREE
Residential Gas Furnace
Smart Equipment (SE) Controls -Commercial Class
Residential Gas Furnace
This course will coveer component familiarization, proper installation practices and emphasize proper start up and commissioning. Including low voltage wiring, setting gas pressure and understanding sequence of operation. This course is divided into two sessions, each being 2 hours in length. Session 1 covers 1 and 2 stage gas furnaces, session 2 covers Modulating gas furnaces and troubleshooting.
Cost: FREE
Residential Heat Pumps
Modulating and Variable Capacity Heat Pumps (YZV & YHM)
Residential Gas Furnace
This course will cover component and accessory familiarization, setting up proper air flow, measuring sub cooling and superheat, verifying refrigerant charge and necessary measurements for commissioning. Certification for the modulating heat pump and variable capacity systems. This class is divided into two sessions, each being 2 hours in length. Session 1 covers installtion practices, session 2 covers technical and troubleshooting.
Cost: FREE
HMH7 Modulating Side Discharge Heat Pump
Modulating and Variable Capacity Heat Pumps (YZV & YHM)
Modulating and Variable Capacity Heat Pumps (YZV & YHM)
This course will cover the components in the HMH7 and the sequence of operation of the HMH7 heat pump. Troubleshooting and maintenance will be discussed. This course is divided into two sessions, each being 2 hours in length. Session 1 is intended for Installers and session 2 is intended for Service Technicians.
Scheduled live classes now available, click on registration below for dates and availability.
Cost: FREE
Modulating and Variable Capacity Heat Pumps (YZV & YHM)
Modulating and Variable Capacity Heat Pumps (YZV & YHM)
Modulating and Variable Capacity Heat Pumps (YZV & YHM)
This course will cover sequence of operation of the 5 Stage Heat Pump and Variable Capacity Heat Pump, know what to expect when the system is operating. Inveter Operation and Service Interface Navigation will be covered with the 5 Stage and Variable Capacity equipment. Discussion of the Adaptive Defrost employed with these units.
Cost: FREE
Basic HVAC Electrical
Compressor (Hermetic) Diagnostics & Replacement
Compressor (Hermetic) Diagnostics & Replacement
This course will cover the Basic Fundamentals of HVAC electricity symbols, definitions, wiring diagram descriptions and reading wiring diagrams.
This course is 2 hours in length and is intended for installation and service technicians.
Cost: FREE
Compressor (Hermetic) Diagnostics & Replacement
Compressor (Hermetic) Diagnostics & Replacement
Compressor (Hermetic) Diagnostics & Replacement
This course is intended for installation and service technicians who diagnose and install compressors. Various compressor models will be discussed, installation practices, wiring, operation and diagnostics will be covered as well.
Cost: FREE
Handling Call Backs
Compressor (Hermetic) Diagnostics & Replacement
HVAC Ductwwork Analysis
This training will include understanding the complaint, root causes of the call back, unit problems vs systemic problems. Also included is conclusion and resolution as well as follow up and follow through. Ths is a 2 hour course.
Cost: FREE
HVAC Ductwwork Analysis
Residential Factory Certified Heat Pump, AC & Gas Furnace Specialist
HVAC Ductwwork Analysis
This training is designed to analyze existing ductwork and recognize how to make improvements to reduce equivalent length and duct pressure when changing out equipment or diagnosing air flow concerns. Air flow basics and duct diagnostics will also be covered. This course is 2 hours in length.
Cost: FREE
Residential Factory Certified Heat Pump, AC & Gas Furnace Specialist
Residential Factory Certified Heat Pump, AC & Gas Furnace Specialist
Residential Factory Certified Heat Pump, AC & Gas Furnace Specialist
Learn the proper procedure to install, startup, test and commission Residential Single & 2 Stage Heat Pumps & AC's, Modulating Heat Pumps, and Residential Variable Capacity Heat Pumps & AC's. This instructor led LIVE class that includes hands-on experiences. This hands on course will cover component and accessory familiarization, setting up proper air flow, measuring sub cooling and superheat, verifying refrigerant charge and necessary measurements for commissioning.
This class is designed for mechanical contractors, project managers, controls technicians, service technicians, and commissioning agents.
Cost: $1990 per Participant
Class is 4 days in length, in person only at Fife, WA or Tigard, OR Training Centers.